Index
- BMSBattery S series
- BMSBattery S06S
- S06ST (torque sensor version)
- S06S-BL (Bluetooth version)
- PWM signals
- Phase B current signal
- Throttle
- BMSBattery S06SC
- BMSBattery S12S
- BMSBattery bottle battery controller
- LCD control panel
- Kunteng mobile app
- Bluetooh
- How to open the controller and solder the programming header
- Hardware mods
- Other controllers
- BMSBattery S06P
- Kunteng 18 mosfets motor controller
- Lishui motor controllers
- JinHui motor controllers
- GreenEBikeKit
- Torque speed
- Motor control scheme of S06S controller
- BLDC 6 steps
- PWM schemes
- So, Which PWM Technique is Best? (Part 1)
- So, Which PWM Technique is Best? (Part 2)
- So, Which PWM Technique is Best? (Part 3)
- So, Which PWM Technique is Best? (Part 4)
- So, Which PWM Technique is Best? (Part 5)
- So, Which PWM Technique is Best? (Part 6)
- So, Which PWM Technique is Best? (Part 7)
- PWM control and Dead Time Insertion
- Low inductance motors
- Throttle Control Modes
- Phase angle FOC
- PWM frequency VS motor eRPM
- Sinusoidal Control of BLDCM with Hall Sensors Based
- Self-Learn Hall Sensor Calibration Mode
- STM8S105 Alternatives
- PID algorithm - negative output values
- Regeneration
- FOC
Datasheets and application notes
- STM8S105C6T6
- Endless-sphere.com forum messages
- 2017.04.25 - Initial forum message
- 2017.05.08 - First flash and debug on a dev board
- 2017.05.18 - First code flashing and running
- 2017.05.20 - more new information
- 2017.08.23 - SxxP versus SxxS versus LSW-675
- 2017.09.01 - Trying to figure out an algorithm to automatically adjust ui8_position_correction_value
- 2017.09.02 - How to do FOC on the BMSBattery S06S/Kunteng STM8 motor controllers
- 2017.09.03 - more ideas about zero crossing for FOC
- 2017.09.05 - measuring IQ current and manually adjusting position_correction_value
- 2017.09.15 - our OpenSource firmware efficiency compared to Lishui 12 FET FOC
- 2017.09.19 - measuring motor current
- 2017.10.23 - FOC and no FOC comparison
- 2018.01.10 - How to measure FOC_READ_ID_CURRENT_ANGLE_ADJUST
- 2018.02.20 - Reading motor phase current from the DC link current (shunt)
01
https://endless-sphere.com/forums/viewtopic.php?f=2&t=79763Passion eBike 6 FET Kunteng Controller (S06S)
by flangefrog » Tue Apr 19, 2016 4:51 pm
I bought a Kunteng 6 FET controller and S-LCD3 from Passion eBike recently. The controller is supposed to be sine wave, although I haven't confirmed that yet. The controller shown in their picture as of today is a 9 fet version. The size and everything else in the description are correct though except for the phase connections which are female bullet connectors, not ring terminals. The throttle connector pinout here is not how it came, I swapped the black and blue pins.
Controller made by Suzhou KUNTENG Electronics Co., Ltd
Bought from Passion eBike
Direct link to product: Passion Ebike 36V or 48V Universal Silver Brushless DC Sine Wave Controller 250W or 350W Electric Bicycle Controller
Sticker on the front says the following:
Model: KT36/48ZWSRD-SLS02D
Rated voltage: DC36V/48V
Rated current: 11A
Maximum current: 22±1A
Speed set: 1-4.2V
Brake input: Low-Level
Low voltage protection: DC30/40±0.5V