Index

About the project

  1. about this documentation in HTML
  2. License

Development tools

  1. Linux
    1. Step-by-step tutorial development tools
      1. Tools to build the firmware
        1. stm8-binutils-gdb
      2. Tools to flash the firmware
        1. How to erase and unlock protected read memory
      3. Hardware tools to flash and debug the firmware
      4. (optional) Tools do flash and debug the firmware
      5. (optional) Tools to debug using serial port
      6. (optional) Tools to see diffs on the source code
  2. Windows
  3. C library
  4. Other tools
    1. Battery voltage boost step-up converter

Motor controllers

  1. BMSBattery S series
    1. BMSBattery S06S
      1. S06ST (torque sensor version)
      2. S06S-BL (Bluetooth version)
      3. PWM signals
        1. very low speed - 6 steps
        2. low speed up to max speed - sineware
      4. Phase B current signal
      5. Throttle
    2. BMSBattery S12S
      1. Programming header
      2. PWM signal at max speed - sineware
      3. Phase B and motor total current signals
    3. BMSBattery bottle battery controller
    4. LCD control panel
      1. LCD protocol
    5. Bluetooh
      1. DIY Bluetooth module
    6. How to open the controller and solder the programming header
    7. Hardware mods
  2. Other controllers
    1. BMSBattery S06P
      1. various info
        1. 01
        2. 02
    2. Kunteng 18 mosfets motor controller
    3. Lishui motor controllers
      1. LSW-675
        1. Datasheets
        2. PWM signals
    4. JinHui motor controllers
  3. GreenEBikeKit

Motors

  1. BMSBattery Q75
  2. BMSBattery Q85
  3. BMSBattery Q100
  4. BMSBattery Q100C

Torque sensors

  1. BMSBattery torque sensor

Datasheets and application notes

  1. STM8S105C6T6
    1. Interrupts

Motor control

  1. Torque speed
  2. Motor control scheme of S06S controller
  3. BLDC 6 steps
  4. PWM schemes
    1. So, Which PWM Technique is Best? (Part 1)
    2. So, Which PWM Technique is Best? (Part 2)
    3. So, Which PWM Technique is Best? (Part 3)
    4. So, Which PWM Technique is Best? (Part 4)
    5. So, Which PWM Technique is Best? (Part 5)
    6. So, Which PWM Technique is Best? (Part 6)
    7. So, Which PWM Technique is Best? (Part 7)
  5. PWM control and Dead Time Insertion
  6. Low inductance motors
  7. Throttle Control Modes
  8. Phase angle FOC
  9. PWM frequency VS motor eRPM
    1. Max motor speed using FOC
    2. Kelly controllers ultra high speed
  10. Sinusoidal Control of BLDCM with Hall Sensors Based
  11. Self-Learn Hall Sensor Calibration Mode
  12. STM8S105 Alternatives
  13. Regeneration
    1. Regen in SimonK firmware

Various

  1. Endless-sphere.com forum messages
    1. 2017.04.25 - Initial forum message
    2. 2017.05.08 - First flash and debug on a dev board
    3. 2017.05.18 - First code flashing and running
    4. 2017.05.20 - more new information
    5. 2017.08.23 - SxxP versus SxxS versus LSW-675
    6. 2017.09.01 - Trying to figure out an algorithm to automatically adjust ui8_position_correction_value
    7. 2017.09.02 - How to do FOC on the BMSBattery S06S/Kunteng STM8 motor controllers
    8. 2017.09.03 - more ideas about zero crossing for FOC
    9. 2017.09.05 - measuring IQ current and manually adjusting position_correction_value
    10. 2017.09.15 - our OpenSource firmware efficiency compared to Lishui 12 FET FOC
    11. 2017.09.19 - measuring motor current
    12. 2017.10.23 - FOC and no FOC comparison
  2. STM8S003 board
  3. 2017.12.01 - Regen ebrake like coast brakes

Clipping

  1. 2017.05.22 - Hackaday Links: May 21, 2017

Smart BMS with bluetooth

2017.10.23 - FOC and no FOC comparison


The next information is about the results of using “very low resolution FOC”.

On the tests I run the motor with or without “very low resolution FOC”. The motor was providing the same mechanical output, was running at the same speed 16km/h and with the same load (on a bike training roller).

With “very low resolution FOC”
As we can see, the phase B current is aligned with the all sensor signal, meaning the Id current is zero and IQ current is max.
The phase B amplitude is 0.94V that represents a current of 5.8A.
images/91-1.png

O next image, the real time log of PWM duty_cycle, motor speed_erps and position_correction_value. position_correction_value is the variable that is automatically adjusted by “very low resolution FOC” algorithm:
images/91-2.png

Without “very low resolution FOC”
For the motor to be able to run at the same speed 16km/h as on the first test, the PWM duty_cycle / energy had to be increased.
The phase B current is not aligned with the all sensor signal (and this misalignment varies with motor load and speed), meaning the Id current is not zero and IQ current is not the max possible.
The phase B amplitude is 1.2V that represents a current of 7.4A.
images/91-3.png