Index

About the project

  1. about this documentation in HTML
  2. License

Development tools

  1. Linux
    1. Step-by-step tutorial development tools
      1. Tools to build the firmware
        1. stm8-binutils-gdb
      2. Tools to flash the firmware
        1. How to erase and unlock protected read memory
      3. Hardware tools to flash and debug the firmware
      4. (optional) Tools do flash and debug the firmware
      5. (optional) Tools to debug using serial port
      6. (optional) Tools to see diffs on the source code
  2. Windows
  3. C library
  4. Other tools
    1. Battery voltage boost step-up converter

Motor controllers

  1. BMSBattery S series
    1. BMSBattery S06S
      1. S06ST (torque sensor version)
      2. S06S-BL (Bluetooth version)
      3. PWM signals
        1. very low speed - 6 steps
        2. low speed up to max speed - sineware
      4. Phase B current signal
      5. Throttle
    2. BMSBattery S12S
      1. Programming header
      2. PWM signal at max speed - sineware
      3. Phase B and motor total current signals
    3. BMSBattery bottle battery controller
    4. LCD control panel
      1. LCD protocol
    5. Bluetooh
      1. DIY Bluetooth module
    6. How to open the controller and solder the programming header
    7. Hardware mods
  2. Other controllers
    1. BMSBattery S06P
      1. various info
        1. 01
        2. 02
    2. Kunteng 18 mosfets motor controller
    3. Lishui motor controllers
      1. LSW-675
        1. Datasheets
        2. PWM signals
    4. JinHui motor controllers
  3. GreenEBikeKit

Motors

  1. BMSBattery Q75
  2. BMSBattery Q85
  3. BMSBattery Q100
  4. BMSBattery Q100C

Torque sensors

  1. BMSBattery torque sensor

Datasheets and application notes

  1. STM8S105C6T6
    1. Interrupts

Motor control

  1. Torque speed
  2. Motor control scheme of S06S controller
  3. BLDC 6 steps
  4. PWM schemes
    1. So, Which PWM Technique is Best? (Part 1)
    2. So, Which PWM Technique is Best? (Part 2)
    3. So, Which PWM Technique is Best? (Part 3)
    4. So, Which PWM Technique is Best? (Part 4)
    5. So, Which PWM Technique is Best? (Part 5)
    6. So, Which PWM Technique is Best? (Part 6)
    7. So, Which PWM Technique is Best? (Part 7)
  5. PWM control and Dead Time Insertion
  6. Low inductance motors
  7. Throttle Control Modes
  8. Phase angle FOC
  9. PWM frequency VS motor eRPM
    1. Max motor speed using FOC
    2. Kelly controllers ultra high speed
  10. Sinusoidal Control of BLDCM with Hall Sensors Based
  11. Self-Learn Hall Sensor Calibration Mode
  12. STM8S105 Alternatives
  13. Regeneration
    1. Regen in SimonK firmware

Various

  1. Endless-sphere.com forum messages
    1. 2017.04.25 - Initial forum message
    2. 2017.05.08 - First flash and debug on a dev board
    3. 2017.05.18 - First code flashing and running
    4. 2017.05.20 - more new information
    5. 2017.08.23 - SxxP versus SxxS versus LSW-675
    6. 2017.09.01 - Trying to figure out an algorithm to automatically adjust ui8_position_correction_value
    7. 2017.09.02 - How to do FOC on the BMSBattery S06S/Kunteng STM8 motor controllers
    8. 2017.09.03 - more ideas about zero crossing for FOC
    9. 2017.09.05 - measuring IQ current and manually adjusting position_correction_value
    10. 2017.09.15 - our OpenSource firmware efficiency compared to Lishui 12 FET FOC
    11. 2017.09.19 - measuring motor current
    12. 2017.10.23 - FOC and no FOC comparison
  2. STM8S003 board
  3. 2017.12.01 - Regen ebrake like coast brakes

Clipping

  1. 2017.05.22 - Hackaday Links: May 21, 2017

Smart BMS with bluetooth

Throttle


Throttle control depends of P3 parameter:

P3 = 1 → speed control: throttle controls the PWM duty_cycle, motor will run up to the max defined speed and up to motor max defined current.
Changing the assist level seems to have no effect.

P3 = 0 → imitation torque control: throttle controls the speed and the torque/max current of the motor.
Max assist level means that motor will run up to max defined speed and up to motor max defined current. Choosing different assist levels will make the motor running up to fractions of those values.

NOTE: each throttle position seams refer to always the same speed value, where the max throttle position may be equivalent to 72km/h (max defined speed possible on LCD5).

How max current control works
If I block the wheel with my hand, the motor keeps doing force/torque and I can read the current value on the power supply. The current is low at the begin of throttle and increases as I increase the throttle.

The current control, at least while the motor is blocked, must be done using AN8 (motor total current) because phase B current signal may be 0 at that situation.

With the motor blocked, it tries to rotate (doing force/torque) but after some seconds it stops.