Index

About the project

  1. about this documentation in HTML
  2. License

Development tools

  1. Linux
    1. Step-by-step tutorial development tools
      1. Hardware tools to flash and debug the firmware
      2. Tools to build the firmware
        1. stm8-binutils-gdb
      3. Tools to flash the firmware
      4. (optional) Tools do flash and debug the firmware
      5. (optional) Tools to debug using serial port
  2. Windows
  3. C library
  4. Various resources
    1. Printf example

Motor controllers

  1. BMSBattery S series
    1. LCD control panel
      1. LCD protocol
    2. BMSBattery S06S
      1. PWM signals
        1. very low speed - 6 steps
        2. low speed up to max speed - sineware
    3. BMSBattery S06P
      1. various info
        1. 01
        2. 02
    4. BMSBattery S12S
    5. BMSBattery bottle battery controller
  2. Other controllers
    1. Kunteng 18 mosfets motor controller
    2. Lishui motor controllers
      1. LSW-675
        1. Datasheets
        2. PWM signals
    3. JinHui motor controllers
  3. GreenEBikeKit

Motors

  1. BMSBattery Q75
  2. BMSBattery Q85
  3. BMSBattery Q100
  4. BMSBattery Q100C

Datasheets and application notes

  1. STM8S105C6T6
    1. Interrupts

Motor control

  1. Motor control scheme of S06S controller
  2. BLDC 6 steps
  3. PWM schemes
    1. So, Which PWM Technique is Best? (Part 1)
    2. So, Which PWM Technique is Best? (Part 2)
    3. So, Which PWM Technique is Best? (Part 3)
    4. So, Which PWM Technique is Best? (Part 4)
    5. So, Which PWM Technique is Best? (Part 5)
    6. So, Which PWM Technique is Best? (Part 6)
    7. So, Which PWM Technique is Best? (Part 7)
  4. PWM control and Dead Time Insertion
  5. Low inductance motors
  6. Throttle Control Modes
  7. Phase angle FOC
  8. PWM frequency VS motor eRPM
    1. Max motor speed using FOC
    2. Kelly controllers ultra high speed
  9. Sinusoidal Control of BLDCM with Hall Sensors Based
  10. Alternatives

Various

  1. Endless-sphere.com forum messages
    1. 2017.04.25 - Initial forum message
    2. 2017.05.08 - First flash and debug on a dev board
    3. 2017.05.18 - First code flashing and running
    4. 2017.05.20 - more new information
    5. 2017.08.23 - SxxP versus SxxS versus LSW-675
    6. 2017.09.01 - Trying to figure out an algorithm to automatically adjust ui8_position_correction_value
    7. 2017.09.02 - How to do FOC on the BMSBattery S06S/Kunteng STM8 motor controllers
    8. 2017.09.03 - more ideas about zero crossing for FOC
    9. 2017.09.05 - measuring IQ current and manually adjusting position_correction_value
    10. 2017.09.19 - measuring motor current
  2. How to unlock protected read memory
  3. STM8S003 board
  4. LOG
    1. 2017.06.19 - SVM current waveforms

Clipping

  1. 2017.05.22 - Hackaday Links: May 21, 2017

Smart BMS with bluetooth

02




Re: Passion eBike 6 FET Kunteng Controller
images/6-1.pngby flangefrog » Thu Apr 21, 2016 10:12 pm
Here is the lights module as promised. The black wire from the black lights connector goes to ground.
images/6-2.pngimages/6-3.pngimages/6-4.png

images/6-5.png

images/6-6.png

images/6-7.png

images/6-8.png

images/6-9.png

The large transistor is a 2SA1013 and the small transistor appears to be a 2SC1815.

This is the schematic. The pins are numbered from left to right looking at the front side with the components.
images/6-10.png

The circuit is fairly simple. The part I'm not certain about is P1. It seems to be some sort of feedback pin so the micro knows the transistors are working.

These are the connections on the main board:
P1: Microcontroller pin
P2: 5V control
P3: Battery voltage from display connector (only on when controller is enabled)
P4: Ground

When the lights board is installed and the lights are enabled P2 is at 3.35V and P1 is 5.7V (seems high as it's directly connected to the micro).