Index

About the project

  1. about this documentation in HTML
  2. License

Development tools

  1. Linux
    1. Step-by-step tutorial development tools
      1. Hardware tools to flash and debug the firmware
      2. Tools to build the firmware
        1. stm8-binutils-gdb
      3. Tools to flash the firmware
        1. How to unlock protected read memory
      4. (optional) Tools do flash and debug the firmware
      5. (optional) Tools to debug using serial port
      6. (optional) Tools to see diffs on the source code
  2. Windows
  3. C library
  4. Various resources
    1. Printf example

Motor controllers

  1. BMSBattery S series
    1. BMSBattery S06S
      1. S06ST (torque sensor version)
      2. S06S-BL (Bluetooth version)
      3. PWM signals
        1. very low speed - 6 steps
        2. low speed up to max speed - sineware
      4. Phase B current signal
      5. Throttle
    2. BMSBattery S12S
      1. Programming header
      2. PWM signal at max speed - sineware
      3. Phase B and motor total current signals
    3. BMSBattery bottle battery controller
    4. LCD control panel
      1. LCD protocol
    5. Bluetooh
      1. DIY Bluetooth module
    6. Hardware mods
  2. Other controllers
    1. BMSBattery S06P
      1. various info
        1. 01
        2. 02
    2. Kunteng 18 mosfets motor controller
    3. Lishui motor controllers
      1. LSW-675
        1. Datasheets
        2. PWM signals
    4. JinHui motor controllers
  3. GreenEBikeKit

Motors

  1. BMSBattery Q75
  2. BMSBattery Q85
  3. BMSBattery Q100
  4. BMSBattery Q100C

Torque sensors

  1. BMSBattery torque sensor

Datasheets and application notes

  1. STM8S105C6T6
    1. Interrupts

Motor control

  1. Motor control scheme of S06S controller
  2. BLDC 6 steps
  3. PWM schemes
    1. So, Which PWM Technique is Best? (Part 1)
    2. So, Which PWM Technique is Best? (Part 2)
    3. So, Which PWM Technique is Best? (Part 3)
    4. So, Which PWM Technique is Best? (Part 4)
    5. So, Which PWM Technique is Best? (Part 5)
    6. So, Which PWM Technique is Best? (Part 6)
    7. So, Which PWM Technique is Best? (Part 7)
  4. PWM control and Dead Time Insertion
  5. Low inductance motors
  6. Throttle Control Modes
  7. Phase angle FOC
  8. PWM frequency VS motor eRPM
    1. Max motor speed using FOC
    2. Kelly controllers ultra high speed
  9. Sinusoidal Control of BLDCM with Hall Sensors Based
  10. Self-Learn Hall Sensor Calibration Mode
  11. STM8S105 Alternatives
  12. Regeneration
    1. Regen in SimonK firmware

Various

  1. Endless-sphere.com forum messages
    1. 2017.04.25 - Initial forum message
    2. 2017.05.08 - First flash and debug on a dev board
    3. 2017.05.18 - First code flashing and running
    4. 2017.05.20 - more new information
    5. 2017.08.23 - SxxP versus SxxS versus LSW-675
    6. 2017.09.01 - Trying to figure out an algorithm to automatically adjust ui8_position_correction_value
    7. 2017.09.02 - How to do FOC on the BMSBattery S06S/Kunteng STM8 motor controllers
    8. 2017.09.03 - more ideas about zero crossing for FOC
    9. 2017.09.05 - measuring IQ current and manually adjusting position_correction_value
    10. 2017.09.15 - our OpenSource firmware efficiency compared to Lishui 12 FET FOC
    11. 2017.09.19 - measuring motor current
    12. 2017.10.23 - FOC and no FOC comparison
  2. STM8S003 board
  3. 2017.12.01 - Regen ebrake like coast brakes

Clipping

  1. 2017.05.22 - Hackaday Links: May 21, 2017

Smart BMS with bluetooth

Motor control scheme of S06S controller

This cheap controllers are a 2nd generation. The first generation like BMSBAttery KU63 did only 6 step and had a shunt to measure motor total current, so no FOC nor current in phase +90º with rotor that is one of the main objectives of FOC.
The 2nd generation controllers, costs only 22€ but added a current sensor ACS712 in ne phase. Now the wave forms are sinusoidal and I think they look at the phase current to make it in +90º in phase with rotor, achieving the most important objective of FOC that is keep the motor rotating using the less energy possible (that will also result in more silent motor) -- amazing for a controller that came inside a metal box and water prof and just by 22€. It uses hall sensors only for track motor rotor position.

Explanation example of AN-8201 FCM8201 Three-Phase Sine-Wave BLDC Motor Controller document:

At 2., the middle HA is where motor flux is and the I phase current must be at 90º after, but as seen, there is a delta teta added to the point of 90º (that point is at end of positive value of HA).
At 3., the motor phase voltage (that we control) we advance delta teta and the result is the phase current will now be at 90º of middle HA (flux) -- this is the point where the motor will have more torque per amp used, the most efficient point:
images/35-1.png